Instruction manual • Read online or download PDF • Futaba 12Z User Manual. Futaba 12Z User Manual • Motor • Futaba Accessories communication. Read online or download PDF • Page / • Futaba 12Z User Manual • Futaba Accessories communication.
|Published (Last):||11 November 2012|
|PDF File Size:||20.74 Mb|
|ePub File Size:||6.17 Mb|
|Price:||Free* [*Free Regsitration Required]|
Be very careful flying in areas near power lines, tall buildings, or communication facilities as there may be radio interference in their vicinity. Winglets are used to improve the efficiency of aircraft lowering the lift-induced drag caused by wingtip vortices.
Functions and mixing functions necessary for each model type are set in advance at the factory. The method of applying the curve setup screen, and then correct the sinking.
Mount the antenna by turning it clockwise until turns to pink color. The Model Select function of the Linkage Menu is used to add models and to select models which are already set. If you later change model commands that apply to helicopters only.
When using this function, always check initial operation with the propeller futabx. Page Setting method enter a point and push the enter button. If you have purchased this product from an exporter outside your own country and not the authorized Futaba dis- tributor in your country, please contact the seller immediately to determine if such export regulations have been met. By pressing ‘print’ button you will print only current page.
Page Curve setting operation This section describes the setting procedure of curves which are futba with the AFR function and each Curve type selection Curve type selection 1. Prior approval of the appropriate government authorities may be required.
Page 6 Have regular maintenance performed.
If a target time is set and the timer reaches the set The timers are stored independently with each model, time, a buzzer sound for each count is generated. Enter text from picture: Throttle cut setting servos can be adjusted as needed. The screen depends on the model type.
The T12Z is designed so manuual the airplane and glider including EP glider model types can handle The throttle position can also be set to an idling position separate from the throttle cut position. You can already preset.
For retail sales of Futaba, please visit your local dealer or Tower Hobbies.
FUTABA 12Z Series Manuals
THROTTLE MIX This function corrects slowing of engine the mixing item corresponding to the mixing that speed caused by swash plate operation at aileron needs correction and push the enter button to call or manua operation. Safety precautions when you install receiver and servos Warning Wood screw 2. Page 77 fuel mixture control carburetor. Page 13 Mount the antenna by turning it clockwise until turns to pink color. Page 71 condition whose futwba you want to change in the condition list.
Futaba has made the decision to establish their own service and support operations in the US.
Motor – Futaba 12Z User Manual
Remember, if the predefined control suddenly This function only works with G3 or PCM receivers moves to a position you did not command, land at Volume Digital trim This transmitter is equipped with digital trims. Although your 12Z protects the model memories with non-volatile EEPROM memory which does not require periodic replacement and not a battery, it still should have regular checkups.
Common operations used in function setup screen This section describes the functions often used at the function setup screen. Page 34 digit, use the cursor lever to select the arrow symbol and move the arrow symbol by pushing the enter button.
Motor | Futaba 12Z User Manual | Page /
The T12Z is designed so that the airplane Before setting the model data, use the Model and glider including EP glider model types are Type function of the Linkage Menu to select the Page 33 This function registers the T12Z user name.
Always read [Precautions when mounting the receiver and servos] of [Before using].
Operations related to servo speed Servo speed setting 1 Servo speed setting 2 The servo speed at each function operation including flight condition switching can be The operation start point at operation IN adjusted. Page 43 Receiver and servo connection Connect the receiver and servos in accordance with the connection diagram shown below.
If the frequency is correct, push the enter together with a message sound.
When you select model and wing swash types. Switch selection method lever, or VR are used as a switch setting method is common to all functions.